SI prefixAn SI prefix is a prefix which can be applied to any unit of the International System of Units (SI) to give subdivisions and multiples of that unit. For example, the prefix "kilo" multiplies by one thousand, so a kilometre is 1,000 metres, and a kilowatt is 1,000 watts. The prefix "milli" subdivides by a thousand, so a millimetre is one thousandth of a metre (1,000 millimetres in a metre), and a millilitre is one thousandth of a litre. The ability to apply the same prefixes to any SI unit is one of the key strengths of the SI, since it considerably simplifies the system's learning and use. The most commonly used prefixes include:
The prefix always takes precedence over any exponentiation; thus km2 means square kilometre and not kilo - square metre. For example, 3 km2 is equal to 3,000,000 m2 and not to 3,000 m2 (nor to 9,000,000 m2). Prefixes where the exponent is divisible by three are recommended. Hence '100 metres' rather than 'one hectometre'. Notable exceptions include centimetre, hectare (hecto-are), centilitre, 1 dm3 (equivalent to one litre), and decibel (one-tenth of a bel, a measure of sound loudness). The obsolete prefixes myria- and myrio- were dropped before SI was adopted in 1960, probably because they do not fit this pattern, no symbol was available (M, m and μ already being used), and were rarely used anyway. The kilogram stands out among all SI base units as the only one that has a prefix. It is derived from the mass of an actual object. The gram is defined as 1/1000th of this object's mass. The accepted English pronunciation of the initial G of giga was once soft, /ˈdʒaɪgə/ (like gigantic), but now the hard pronunciation, /ˈgɪgə/ (like giggle), is probably more common. However, both pronunciations are likely to be understood by most English speakers.
Use outside SIThe symbol "k" is often used to mean a multiple of a thousand, so one may talk of "a 40K salary" (40,000), or the Y2K problem. Note that in these cases an upper case K is often used, although it should be noted that using an uppercase K is never correct when writing under the rules of the SI, since the K stands for the kelvin. Also, it is often used as a prefix to designate the binary prefix kilo = 210 = 1024. Non-SI unitsSI prefixes rarely appear coupled with imperial units except in some specialised cases (e.g. megaton). They are often used with cgs units in situations where these are still found (e.g. millitorr). They are also used with "natural" units in some fields (e.g. megaelectron volt, gigaparsec). ComputingThe prefixes k and greater are common in computing, where they are applied to information and storage units like the bit and the byte. Since 210 = 1024, and 103 = 1000, this led to the SI prefix letters being used approximately to denote "binary" prefixes as follows:
However, these prefixes usually retain their powers-of-1000 meanings when used to describe rates of data transmission (bit rates): 10 Mbit/s Ethernet runs at 10,000,000 bit/s, not 10,485,760 bit/s. The problem is compounded by the fact that the units of information (the bit and the byte) are not part of SI. Although it is clearer symbology to use "bit" for the bit and "b" for the byte, "b" is often used for bit and "B" for byte. (In SI, B stands for the bel.) French-speaking countries often use "o" for "octet", a synonym for byte, but this is unacceptable in SI because of the risk of confusion with the zero. Consequently, the International Electrotechnical Commission (IEC) adopted new binary prefixes in 1998, formed from the first syllable of the decimal prefix plus 'bi' (pronounced 'bee'). The symbol is the decimal symbol plus 'i'. So now, one kilobyte (1 kb) equals 1000 bytes, whereas one kibibyte (1 KiB) equals 210 = 1024 bytes. Likewise mebi (Mi; 220), gibi (Gi; 230), tebi (Ti; 240), pebi (Pi; 250), and exbi (Ei; 260). Although the IEC standard does not mention them, the sequence can be readily extended to zebi (Zi; 270) and yobi (Yi; 280). The adoption of these prefixes has been very limited. † Britain, Ireland and Australia previously used the long scale number name conventions, but have now largely switched to the short scale usage. Note in particular that above a million and below a millionth, the same name has different values in the two naming systems, so billion and trillion (for example) become unfortunately potentially ambiguous terms internationally. Using the SI prefixes can circumvent this problem. See number names for the details. See alsoReferencesThis article was originally based on material from the Free On-line Dictionary of Computing and is used under the GFDL. External links
Categories: Units of measure | SI prefixes |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
This article is licensed under the GNU Free Documentation License. It uses material from Wikipedia article. Browse Wikipedia for more information. |